Why Does a Forklift Pull to One Side?

Nov 10, 2026

Leave a message

Why Does a Forklift Pull to One Side?

 

 

A forklift should normally travel in the direction selected by the operator without constantly needing steering correction.

If the truck begins pulling noticeably to the left or right, the first question is:

Does it pull during normal travel, or mainly when braking?

That distinction matters because the two symptoms can point toward different systems.

Possible causes include tires, wheel bearings, steering components and brakes. CLARK forklift troubleshooting guidance, for example, lists mismatched tires, wheel-bearing problems and bent steering linkage among possible causes of a truck pulling to one side.

Start With the Tires

Tires are one of the simplest areas to check.

Possible problems include:

  • Different tire sizes on the same axle
  • Uneven tire wear
  • One newer tire paired with a heavily worn tire
  • Incorrect pneumatic tire pressure
  • Tire or rim damage

CLARK specifically identifies odd-size or mismatched new and worn tires on opposite sides as a possible cause of pulling.

Toyota also recommends checking for uneven tire wear between the left and right sides and maintaining pneumatic tires at the manufacturer's specified pressure.

This is especially important on heavy forklifts using dual front tires.

The inner and outer tires of a dual assembly both need attention. A problem hidden on the inner tire can easily be missed during a quick walkaround.

Pneumatic and Solid Tires Need Different Checks

Not every forklift uses pneumatic tires.

For example, the current Propolift 16 Ton Forklift is available with pneumatic tires, with solid tires optional.

If the truck uses pneumatic tires, inflation pressure needs to be checked against the specified value.

If it uses solid tires, pressure is not relevant, but uneven wear, damage, tire diameter and installation condition still matter.

So the troubleshooting process should always start from the actual tire configuration rather than a generic checklist.

Does It Pull Only When You Brake?

If the forklift travels straight normally but moves left or right when the brake pedal is applied, uneven braking deserves attention.

A Hangcha forklift service manual lists several possible causes of uneven braking, including:

  • Improper brake adjustment
  • Uneven tire pressure
  • Incorrect wheel-bearing adjustment
  • Restricted brake lines

and describes the symptom as the forklift leaning or pulling toward one side.

Older forklift technical manuals likewise identify contaminated or unevenly adjusted brake components as possible causes of brake pull.

The important point is:

Pulling during braking should not automatically be diagnosed as a steering problem.

The brake system may be applying different force on the left and right sides.

Wheel Bearings Can Affect Directional Stability

Wheel-bearing condition is another area worth checking.

Bearings that are too tight, loose or damaged can affect wheel movement and steering behavior.

Both CLARK and Hangcha troubleshooting information identify wheel-bearing condition as a possible factor when a forklift pulls or brakes unevenly.

This is not something that should be corrected by randomly tightening the wheel assembly.

Bearing inspection and adjustment should follow the service procedure for the actual truck.

Check the Steering System

If tire condition is normal and the truck still wanders or pulls during ordinary travel, steering components may need inspection.

Depending on the forklift, this can include:

  • Steering cylinder
  • Steering linkage
  • Steering arms
  • King pins or bearings
  • Hydraulic steering components
  • Axle alignment

CLARK troubleshooting guidance lists bent steering arms or connections among possible causes of one-sided pull, while other forklift maintenance guidance identifies steering-cylinder leakage or damage as a cause of wandering or pulling.

Because conventional counterbalance forklifts normally steer from the rear, a steering problem may feel different from a passenger vehicle.

Do Not Ignore the Drive Axle

On a conventional counterbalance forklift, the front axle normally serves as the drive axle.

If the symptom appears together with abnormal wheel resistance, brake drag, bearing noise or drivetrain noise, the front-end system may need to be inspected as a whole rather than treating the steering wheel as the only possible cause.

For heavy duty forklifts, tires, wheel hubs, brakes and axle components work together under very high loads.

Tread Width Is Not the Problem by Itself

Buyers sometimes notice that front and rear wheel positions are different and wonder whether this means the truck is "not aligned."

That is not necessarily the case.

The forklift tread width can be different between the front and rear axles by design.

A published tread dimension should therefore not be confused with wheel misalignment.

The concern is whether the truck has developed an abnormal change from its intended geometry or component condition.

Check the Working Surface Too

Not every directional problem comes from the forklift.

A truck may appear to drift because it is operating on:

  • A cross-slope
  • Uneven concrete
  • Deep wheel ruts
  • Soft ground
  • A badly crowned road surface

Before dismantling components, test whether the same symptom occurs on a suitable level surface.

If the truck travels straight on level ground but pulls consistently in one part of the yard, the site itself may be contributing to the behavior.

What Information Helps With Diagnosis?

When a customer reports:

"The forklift keeps going to the left."

we would normally want to know:

  • Does it happen loaded and unloaded?
  • During travel or only braking?
  • At low speed or higher speed?
  • On every surface?
  • Are the tires pneumatic or solid?
  • Are tire sizes and wear similar left to right?
  • Is there abnormal brake or wheel-hub temperature?
  • Is there steering play or unusual noise?
  • Did the problem appear suddenly or gradually?

A short video of the truck traveling straight on a level surface can also be useful.

When Should the Forklift Stop Working?

OSHA requires forklifts to be inspected before use and includes tires, steering and brakes among the items that should be checked. A truck that is defective or unsafe should be removed from service until corrected.

If the forklift develops strong directional pull, unpredictable braking, abnormal steering movement or significant tire damage, continuing normal heavy-load operation is not a good troubleshooting method.

The condition should be inspected first.

Final Thoughts

A forklift pulling to one side does not point to one single component.

A useful troubleshooting sequence is:

Check the surface → inspect the tires → identify whether the pull occurs during braking → check wheel bearings → inspect steering and axle components.

The most important clue is when the pulling happens.

A truck that drifts during normal travel may have a different problem from one that only changes direction when the brake pedal is applied.

Separating those two symptoms first makes the rest of the diagnosis much more efficient.

 

References

  1. OSHA - Powered Industrial Trucks: Pre-Operation Inspection.
  2. OSHA - Sample Daily Checklists for Powered Industrial Trucks.
  3. CLARK - Industrial Truck Troubleshooting Guide: Steering and Directional Pull.
  4. Hangcha - Forklift Service Manual: Uneven Braking Troubleshooting.
  5. Toyota Material Handling - Signs It's Time to Replace Your Forklift Tires.